China Top 10 Manufacturer 1 ton Industrial Oil Fired Steam Boiler
Construction of gas china top 10 manufacturer 1 ton industrial fired steam boiler steam requirements for the construction of a gas boiler requirements, gas steam boiler installation for the construction of the boiler room have certain requirements, must comply with national requirements in the construction process. Gas and steam 1, the construction of a gas steam boiler room requirements 1) boiler room must comply with the "boiler energy saving technical supervision and management regulations" and "industrial boiler room design specifications" requirement. Gas steam 2) boiler room should have sufficient light and good ventilation, have the necessary antifreeze measures. And boiler room should stay away from schools, housing and densely populated areas. 3) the position should be close to the boiler room heating equipment, in order to reduce head losses and heat loss from the hot oil piping circulating pump. 2, furnace heat carrier device is arranged in claim 1) the sump should be lower than the lowest position of the heat carrier furnace and heat system 1 m, in order to put the net organic heat boilers and systems, sump and furnace heat carrier spacing less than 5 m or separated by a partition wall. It should be fitted with a sump exhaust pipe, which exhaust pipe diameter should be large and specifications than the inflation tube. 2) position of the expansion tank should be higher than the other devices and the piping system, the system must be higher than the maximum bottom level 1.5 m. It should not be installed directly above any one boiler, organic heat carrier to prevent overflow cause a fire. 3) the sump vent pipe, expansion tank, should be connected to the outdoor safety. Can not be mounted on the vent pipe to the valve, to ensure that the tank, the expansion tank to atmosphere to ensure atmospheric pressure operation. 4) the high volume of the expansion tank should be greater than 1.3 times and all the organic heat carrier furnace heat the entire heating systems is at the operating temperature is increased due to thermal expansion of volume. 5) low volume tank furnace heat carrier to be less than 1.2 times the total amount of organic heat. 6) hot oil circulation pump should be at least four weeks for 0.5 m space, and the inspection to ensure the installation routine, the need for maintenance.
What are the technical parameters of the gas boiler boiler parameters are: 1, boiler capacity, which is the output Q, units of china top 10 manufacturer 1 ton industrial fired steam boilers are tons / hour representation. Hot water boiler for heat MW / h represents; 2, pressure P, the unit is Mpa; 3, steam (or superheated steam) Temperature q, in degrees Centigrade. Hot water boiler expressed in terms of outlet temperature and return water temperature. Another area of the heating surface of each grate area, fuel type, fuel consumption, water temperature, total drag, with the wind (the wind drums) the amount of exhaust gas temperature and the like. The expression model are: the number of drum (e.g., single drum D, S, double drum); drum arrangement (transverse type H, the Z vertical type); combustion (chain L, G stationary grate etc.); a fuel type (coal a, gas Q, Y fuel, etc.); a steam boiler is usually "tons / h" or "t / h" is the capacity of the boiler. With "Mpa" or "MPa" (old unit of "kgf / cm 2" or "kgf / cm2") of the rated pressure of the boiler, it represents the temperature at the rated pressure saturated steam and superheated by "deg.] C" (Celsius) steam temperature. Thermal Efficiency Heat Transfer Fluid is a boiler furnace or a thermal transfer process, heat is absorbed by water, steam or thermal oil, accounting for complete combustion of the fuel into the boiler heat released percentage capacity of 1t / h steam boiler, i.e. It indicates that the boiler may be over 1 hour into water of 1 ton capacity of saturated steam under pressure; 0.7MW of such water heaters and furnaces heat Transfer Fluid representations may generate heat corresponding to 0.7MW power over 1 hour ( equivalent to one ton of steam heat). Two water boiler is the heating means for the hot water boiler working fluid. Usually "MW" (MW), with the old unit "when Wan kW /" or "million kcal / h", namely "104kcal / h" is the capacity of the boiler, with "Mpa" represents the rated pressure of the boiler, with "℃" the hot water temperature.
Due to the special nature of the industrial park location, we are more to consider whether the boiler with green features in the choice of boiler equipment. According to our survey of the entire boiler industry, quick side has considerable experience in research and development in the field of environmental cleaning boilers, boiler equipment while also providing low pollutant emissions for Beijing more enterprises and institutions, we are fully confident that the fast boiler ability. --customer feedback
Newer kinds of textiles and upcoming producers other than the traditional ones call for judicious selection of products. Here you can source factories and companies according to your business needs for better profit margins. Textile factory needs tones of steam in its dyeing and others. Installing diesel oil fired boiler or natural gas fired boiler, it is very convenient to operate and maintain. Typically, textile process includes clean cotton, carding, combing, drawing, roving, spinning, winding, twisting, shaking Line, etc. Ever expanding apparel and clothing industry poses new challenges before the textile manufacturers and producers. Steam boiler is an important equipment in textile factory.