Fangkui Boiler aims to "warm the world", and we provide target customers worldwide with boiler equipment and service guidance to meet their needs. At present, we have provided boiler equipment and solutions for customers in more than 80 countries and regions, including Russia and Bangladesh, to promote the production efficiency of customer enterprises.

Boiler basic knowledge and principle: as a heat carrier, pump forced circulation of liquid phase, then return to reheating, direct-flow special industrial furnace. Widely used in foundry sand molds such as petrochemical, textile, printing and dyeing, plastics, rubber, food processing, wood processing, asphalt heat, carton production, vegetable dehydration, drying and so on. Boiler is an energy, safe, heating equipment, is an ideal alternative to steam boiler products. The working principle is that the oil heater (endothermic) (organic heat) which is transported to the various thermal equipment after heating, the heat conduction (heat energy release), and then back to the furnace, forming a closed circle in the sense of meaning. In order to achieve the purpose of heating in the process of education. Performance and characteristics: 1, low pressure and high temperature. With the increase of temperature, the viscosity of the oil will continue to decrease the resistance of the system, but also reduce the working pressure, more conducive to safe operation and safe operation. Steam boiler is a high temperature and high pressure plume. 2 the heating system adopts hot water and equipment inlet and outlet temperature of 20? 30 degrees closed-circuit forced circulation heat can be recycled repeatedly there is no waste thermal efficiency is high energy-saving effect is remarkable. (3) the pressure of the heating system is low and the requirements of the pressure equipment and its system will also be reduced accordingly. Therefore, the steam pot required by the production process is accordingly reduced. The furnace is simple and the investment cost is low. 4, the thermal efficiency of various loads can be maintained at an optimal level, and can be adapted to the production of heat load requirements of the following types of 320 degrees, temperature can be accurately adjusted and controlled. 5, heaters to increase two to three times the cycle can provide a wide range of temperature processes for a variety of equipment to meet different temperatures that greatly reduce the need for equipment investment.

Boiler steam temperature affect the safety and economy temperatures above will be lower than the rated temperature of the device, it will have a bad effect. If the temperature exceeds its rated value, the boiler will cause overheating of the relevant metal material, material creep acceleration, will shorten the life of the boiler. If the temperature is too high, but some of the key components of the boiler would cause damage, can also cause serious and even superheater tube rupture. If the temperature is lower than the rated temperature, vapor enthalpy is reduced, increased air consumption, decreased economy. This will reduce the thermodynamic cycle efficiency of the plant, the steam humidity at the last stage blades of the gas turbine increases, causing erosion and damage to water droplets gas turbine blades, affect the safe operation of the gas turbine. Ruoyin with water vapor causes a decrease in temperature, the moisture in the salt impurities formed in the superheater scale, pipe valves, gas turbine blade, because the superheater lead to reduced heat transfer, the temperature decreased, damage increased wall temperature; and cause the valve plug, the operation failure; and a gas turbine blade erosion, loss of balance and vibration occurs. Temperature fluctuations reason superheater actual heat transfer the vapor does not reach the required amount of heat absorbed corresponding balancing. When the heat absorbed is greater than the heat transfer, the temperature rise; conversely decreased. Many factors affect the temperature change, including both gas side and the vapor side. Such as boiler load increased, but also to ensure the boiler load unchanged or decreased in order to prevent pressure shall increase the amount of fuel and air supply, strengthen the burning, causing the furnace exit flue gas temperature of the flue gas volume increases and lower water temperature , temperature increase; If the oil and gas fuel is combusted in the furnace carbon black is not fully formed, into the superheater flue causing secondary combustion, but also greatly increase the superheat temperature. Reducing the temperature of the main reasons: improper adjustment of combustion, low flame center furnace; superheater area is small, or too much leakage at the furnace wall; Save water flow rising or temperature reduction; drum water level or high gas-water separator separating efficiency is lowered, the humidity of the vapor is increased; superheater tube fouling, reduced heat absorption and the like.

Gas-fired steam boiler equipment maintenance equipment maintenance points 1: 1, or twice a day to clean up slag. 2, washed once or twice a heater dust (ash door with the appliance design) weekly. 3, once or twice a month, or butter oil feeding helical gears and bearings induced draft fan. 4, a monthly injection of butter or oil to the fan motor bearings once or twice. 5, a boiler must be 2-4 times the annual emissions (emissions must promptly after filling water). 6, poor water quality, in use. 2. Before, must soften water. Gas fully automatic diesel oil or fired hot water boiler with environmental protection, energy conservation, safety, salient features fully automatic operation, and ease of use. In addition, due to the operation of the economy, government policies to encourage, gas hot water boiler more and more people of all ages. Daily inspection equipment: 1, the fan regularly checks whether there is a feed screw loosening device, whether there is abnormal noise. 2, regular inspection trip tank float valve is normal replenishment, water pressure is normal. Biomass boiler categories: biomass boilers Horizontal, vertical biomass boilers. Biomass gas thermal oil heaters, biomass steam boiler, biomass hot water boiler, biomass oil furnace. 3, if equipped with a pump, replace circulation pump on a regular basis, and check whether the pump is working properly. Function gas boiler the ignition system that ignites the mixture of air and fuel, its main components are: the ignition transformer, the ignition electrode, a high voltage electrical cable fire. A more secure electronic ignition system called ignition pulse, is widely used Zhuoyi energy saving gas boiler manufacturers. Which facilitate saving, can simply press a finger, and safe, does not occur due to unexpected accidents occur flame, once the stall state occurs, the control system can close the solenoid valve, off the gas passage. 4, regular inspection equipment grounding cable is connected correctly. 5, to ensure the normal supply of fuel in the hopper, so as to avoid non-fuel flameout downtime. 6, it should be observed regularly combustion of the fuel in the combustion chamber. Incomplete combustion of fuel, smoke or large block to form sulfur, the sulfur should be promptly removed block and the governor to adjust the feed flow rate ratio of the fan, to achieve the desired combustion.