industrial gas oil coal biomass fired steam boilers
In recent years, the state environmental protection is all the more attention we as a company with the times, in order to respond positively to the implementation of the national environmental protection requirements from coal to gas project. But the choice of boiler suppliers in this area quite a headache, after repeated comparison and investigation, we chose to partner with fast boiler. Fang did not disappoint quickly proved that the recommended boiler operation after use to fully meet our needs, both energy saving and environmental protection, high thermal efficiency, to a certain extent, cost savings for our fuel. --customer feedback
The final step is to select which type of industrial oil coal biomass fired steam boilerss currently on the market have the type of fuel boilers, electric boilers. Due to the current state for the "coal to electricity," the advocate, more companies may choose an electric boiler, but there are energy consumption, safety issues such as the traditional electric boiler, by contrast, the crown than conventional electric steam boilers boiler energy saving more than 30% compared to conventional steam boilers have increased security.
6 tons adjusting a combustion gas industrial oil coal biomass fired steam boilers, normal combustion boiler three basic aspects of indicators include a uniform supply of the fuel, reasonable ventilation, adjustment the combustion. 1, to maintain the high temperature of the combustion chamber temperature of the upper layer is preferably in the 1100 ~ 1300 ℃, flame orange in color. Flame reddish color indicates that the amount is not enough to the wind, the color white indicates that excessive wind. It should be appropriately adjusted. 2, fuel ash to reduce ash content in the combustibles to be below 10%. 3, reducing the temperature of the boiler flue gas exhaust gas temperature should be controlled below 200 ℃. 4, holding furnace negative excess air boiler is 1.2 to 1.4, by adjusting the balance of the blowers to maintain the furnace pressure is -20 ~ -30Pa. 5, the thermal efficiency of the boiler to improve the thermal efficiency of the boiler should be kept above 60%. II. Combustion Adjustment 1, the amount of fuel to air required for combustion and the amount of a reasonable distribution. Ventilation should first increase the amount of fuel increases, it should first reduce the amount of fuel supply reduced ventilation. 2, the thickness of the seam and seam thickness configuration grate speed is 80 ~ 120mm grate speed at high, middle and low profile configuration of several commonly used methods:. 9a rapid combustion of thin seam b c thick seam in low combustion. 3 thick seam combustion speed, the segment with the wind blowing principle: burn promoting intermediate ends. That is, after the coal into the coal starts to warm up the shutter, fire line front arch, the primary combustion zone, the middle grate to burn the rear grate zone. Normal combustion conditions are: fuel from the coal at the beginning of the fire shutter 300mm, uniform flames, the fire bed formation, at the end of combustion from the end of the grate 300 ~ 500mm. 4. maintain proper furnace temperature to avoid coking. The fire bed to maintain the homogeneous combustion, to avoid burning fire bed obliquely. 6. The residence time of the fuel on the grate in less than 30 minutes.
A number of national influence energy consumption industrial oil coal biomass fired steam boilers coal to natural gas has been vigorous work, it should be transported steam boiler, very big eliminate the dust pollution, discharge of toxic gases and secondly nitric oxide, also got curb. Energy consumption is crucial mark measuring steam boiler, a good start and that is that work together to explore under the influence of a number of cases the energy consumption of steam boilers. Through the investigation of the persons concerned, the loss of heat from steam boilers bear the main two areas: combustion air-fuel ratio does not smoke emissions standards-related heat loss. Reduction of heat loss will install smoke emission in the flue gas heat recovery steam boiler terminal fitting, or should be transported more leading type condensation recovery boiler. Combustion air-fuel ratio standard fault summary: a conventional steam boiler burner ejector type, formed air-fuel ratio can not occur motorized adjustment. Some of the steam boiler with a mechanical blower burner, causing air-fuel ratio standard there are several aspects later: the main air-fuel ratio standard case encompass fall into two categories: air flow when exceeded, there will be an endless excess cold heat transfer, resulting in high energy cost of steam boilers, steam boilers reduced energy consumption; when the airflow is not enough, will have not exactly lit, the energy consumption caused by steam boiler weakened.