The main structure of a natural gas boiler consists of a boiler shell, a tank, a switching chamber, a smoke pipe, etc. The boiler is suitable for various fuels such as light oil, heavy oil, natural gas, liquefied gas, and so on. The boiler has a reasonable structure and a double-layer reverse burning. It is beneficial to make full use of flue gas, and has the characteristics of small area, convenient installation and good steam quality. The working principle of natural gas boiler is: the water enters the boiler through the inlet, the water quality that meets the heating standard after the boiler is heated, the water is fed into the indoor radiator through the circulating pump, the heating is heated by radiation and convective heat transfer, and the water flowing through the radiator is flowing through the water of the radiator. Go back to the boiler and heat it up, and then go back to it. It flows into the radiator, so that it circulates over and over again. Moreover, the natural gas boiler system can also provide users with hot water to meet its basic needs, the temperature of the water quality in the boiler and the indoor temperature, after temperature sensor processing, the temperature signal is transmitted to the single-chip microcomputer. Through the corresponding driving circuit, to adjust the size of the corresponding pipe valve, and then by controlling the water quantity to control the water temperature, to achieve the purpose of heating, the user can also select the appropriate circulation pump according to the size of the heating range. This is also more economical and convenient.

Finally, the delegation went into the manufacturing plant, the robot welding expressed strong interest in the robot field operations after watching the situation, I am using for manufacturing more refined variety of highly intelligent boiler equipment expression of praise. Mr. Liu is also the site to watch the robot control platform, careful observation stations located at the edge of the station systems. Side of photography Henan Daily reporter Chen Hui spoke to the tour group members in the field, this robot is currently in the province is a "little red network", has been the provincial media repeatedly reported.

Electric cheap price industrial burner for steam boiler to be taken by each of the cathodic protection measures components of the electric steam boiler is made of different materials. In order to prevent galvanic corrosion, cathodic protection measures must be taken. Sewage treatment electric steam boilers. Bottom electric steam boiler blowdown can prevent flue gas condensation. Since the flue gas is flue gas condensation (diesel or natural gas) and the flue gas temperature in the aqueous too low, water generated. A portion of the moisture is discharged from the chimney, the chimney wall is absorbed, the rest is deposited on the bottom of the chimney. Water produced by the following factors influence: flue gas temperature (efficiency 91%, the flue gas must be at a temperature of 170 ℃) where the total surface area heat chimney, chimney and chimney material. Maintenance of the burner. Electric steam boiler and burner maintenance, repair after steam supply. Because the products of combustion will corrode the boiler, clean up carbon deposits, therefore, not allow the products of combustion in the boiler memory stay too long. We first opened when an electric steam boiler burner door, the rear housing panel removed, unscrew the screws electric steam boiler cleaning the rear opening. Clean fuel gas piping with a wire brush. With a soft brush to clean the combustion chamber. Electric steam boiler to remove residue in the boiler, the cleaning opening is screwed on the screw, closing the burner door seal check is complete. If electric steam boilers installed in areas where temperatures below 0 ℃ must take the following precautions: If electric steam boiler room outside, the room temperature drops below 15 ℃ or 18 ℃, the electric steam boiler running all day long. If no one in the room for a long time, the water should be emptied in electric steam boilers.

Spark ignition rods gas boiler, but because the misfiring spark ignition rods gas boiler misfiring but the reasons: 1, the cyclone disc space ventilation is blocked carbon, poor ventilation. 2, dirty oil nozzle clogging or wear. 3, the throttle angle is set too small. 4, the firing bar from the leading edge from the oil nozzle tip inappropriate (too protruding or retracted) 5, the first solenoid valve is an oil debris blocking gun (gun small kerosene). 6, oily or too viscous to flow easily clogged or the oil filtration system the valve is not opened, so that insufficient suction pump, oil pressure. 7, the filter pump itself blocked. 8, the oil more water (boiling abnormal noise within the heater). Gas boiler ignition spark rod action but misfiring are: clear; the first washing, such as not renewed; turndown test; adjusting the distance (in 3 ~ 4mm as well); Remove cleaning (cleaning the parts diesel) ; For more information about oil oil oil, information technology please pay attention to the public number of oil rings. Check the pipeline and oil filters, insulation equipment; peripheral screw pump removed, carefully remove the cover inside out net oil, diesel oil immersion; renewal of the test oil. When the gas boiler and turn the fire a small fire normal, off, or flashing the causes of instability: 1, air volume damper setting fire too. 2, oil fires micro switch valve (damper outermost that group) inappropriate setting (set throttle air flow rate is greater than the fire). 3, oleaginous easy to spray viscosity is too high (heavy). 4, and the nozzle plate spacing cyclone inappropriate. 5, fire nozzle worn or dirty. 6, the preliminary fuel tank temperature is too high, so that the steam not smooth oil pump oil feed. 7, gas hot water boiler fuel oil water. When a small fire gas boiler normal and turn the fire extinguished or flashing instability action: Test gradually reduced; heating temperature; adjusting the distance (between 0 ~ 10mm); clean or replace; i.e., set to about 50 deg.] C may be; or drain oil change.