industrial oil burner for hot water boiler Agent horizontal
Improve the thermal efficiency of the process wns gas boiler, oil-fired boiler which chemical incomplete combustion heat loss and mechanical incomplete combustion heat loss. Because almost no ash after combustion of the gas boiler, solid and liquid fuels without mechanical incomplete combustion, there is no need to consider the mechanical incomplete combustion of the gas boiler heat loss. In all heat losses, heat losses have tremendous proportions, when the high thermal efficiency of boilers, heat losses so the total loss of the main heat losses of fuel gas-fired boiler flue gas heat loss is the exhaust gas temperature and For air excess factor. When the exhaust gas temperature decreases, high thermal efficiency can be obtained, for example, a conventional three-pass steam boiler, furnace used in the past straight and smooth smoke tube, must increase the heating surface is arranged to make the exhaust gas to an acceptable degree, the theoretical discharge around the smoke heat loss. Potshell causing significantly increased diameter, wall thickness increased, greatly increased metal consumption, thus further reducing the exhaust gas temperature should be greatly restricted. From the aspect of heat transfer is not only now consider only the heated area, the use of new technology enables heat transfer performance significantly increased, the difference between the heat transfer overcomes the disadvantages of the past performance of the boiler, so that the exhaust gas temperature decreases, the structure is more compact. Center back boiler combustion boiler is preferably small foreign structure, although the two-pass boiler, the heated area is small, but the use of the turbulator charming, the purpose of enhancing the turbulence of the flue gas, disrupt laminar flow boundary wall, reducing the thermal resistance, increasing the heat transfer coefficient, a smaller heating area to achieve the same high thermal efficiency. Lower exhaust gas temperature limit in theory, the exhaust gas temperature can be reduced to very low or even close to the ambient temperature, for maximum thermal efficiency. However, in practice, due to the reduction of the exhaust gas temperature, low temperature corrosion will cause, therefore, the exhaust gas temperature can drop too low, in order to ensure that the wall temperature is higher than the main boiler heating surface flue gas dew point temperature. Therefore, low-temperature corrosion has become a major obstacle to reduce exhaust gas temperature and improve the thermal efficiency of the boiler. Tail auxiliary heating surface increases, further reducing the exhaust gas temperature, fuel gas wns improve thermal efficiency of the boiler as the oil, gas fuel burn easily wns type gas boiler air preheater generally not disposed. The economizer means is a common energy, which can be recycled flue gas was able to effectively reduce exhaust gas temperature. Separation type condensing gas boiler is out of the main boiler heating surface, the installation of the condensing heat exchanger. In one aspect of the flue gas absorption can significantly reduce the smoke temperature, reducing heat losses, on the one hand the absorption of part of the potential condensing water vapor released, increasing the effective use of heat of the fuel. Ash cleaning, to ensure that the heating surface of the scale wns boiler thermal efficiency of the boiler, the presence of soot fouling and heat transfer resistance increases, reducing the heat transfer effect. The thermal conductivity of the scale and soot is almost of the same order of magnitude, with the increase in scale, soot, the exhaust gas temperature rapidly increases, the thermal efficiency is significantly decreased. So, keep the boiler heating surface inside and outside clean, efficient heat transfer, thermal efficiency and to ensure the safe and economic operation of boilers, boiler fuel gas-fired boiler ash cleaning is required.
The competition, the segment is slowly 45 contestants only a female welder, most of the other competitors from China Electric Power Construction, veteran welders in the petroleum, petrochemical, and other large number of country prefix units, with a very rich practical operation of work experience. Faced with numerous welding expert, slowly segment did not flinch and fear, but to actively exercise their welding ability, the old master who humbly ask to try a variety of different welding methods, and repeat the training to do practice makes perfect. By her welded boiler parts forming the United States, no weld defects neat; in her station, welding clean, neatly stacked tools, work order. It is because of her usual work down to earth, hard work and practice, lay a solid foundation for the success obtained.
What works and characteristics of natural gas boilers are? Gas-fired, the main structure of a shell boiler, furnace, turning smoke chamber, and other components of the smoke tube boiler is suitable for light oil, heavy oil, natural gas, gas and other fuels, the boiler reasonable structure, double-layer anti-burn, facilitate flue gas is fully utilized, and also has a small footprint, easy installation, high steam quality and so on. Works natural gas boilers are: water through the inlet into the boiler, heating boiler after heating meet the water quality standards, into the interior through the radiator circulating pump to heating by radiation and convection heat transfer, water flowing through the radiator, back inside the boiler is heated, and then again into the radiator, so the cycle is carried out. And the system of gas-fired, can also provide hot water to meet their basic needs, the boiler water temperature and the indoor temperature, a temperature sensor after the treatment, the temperature signal is transmitted to the microcontroller, through the corresponding drive circuits to adjust corresponding pipe size valve, and further by controlling the temperature of water, heating to achieve the purpose, the user according to the size of the heating range, select the appropriate circulating pumps, to do so is also more economical and convenient.
Some knowledge boiler Introduction: boiler is an energy conversion device, the energy input to the boiler chemical energy, electrical energy, a boiler with a steam output of the fuel in the constant heat, high temperature water or organic heat carrier. Today introduced are several little knowledge about the boiler. 1, a way to improve the efficiency of the boiler A which:? ⑴ low heat losses: prevent heating surface fouling and coking, the rational use of the burner, controls the blower inlet air temperature, water temperature of attention to the impact, into the furnace to avoid excessive wind note impact milling system operation; ⑵ mechanical incomplete combustion to reduce heat loss: rationally adjust the fineness of pulverized coal, the excess air ratio control of appropriate, attention combustion adjustment; ⑶ quality assurance fired boilers; ⑷ reduce soda losses: guaranteed boiler quality water supply, installation and maintenance to improve the quality of the steam separator means, to maintain the operation of the boiler load, the water level, steam pressure and other parameters of stability, so that the boiler water separation apparatus operating under normal conditions; ⑸ index management adhere to the small boiler. ? What are the reasons boiler fire answer: ⑴ low boiler load, low temperature furnace, combustion temperature, combustion oil investment is not timely; ⑵ poor coal quality, low volatile matter, ash is too large; ⑶ air volume to adjust properly, once too high wind speed, wind powder imbalance, the excess air ratio is too large; ⑷ excessive negative pressure maintaining furnace; ⑸ bunker powder level is too low or fallen powder to the powder to make the powder unevenness; ⑸ large depression coke furnace, disturbances in the furnace is too large; ⑹ ash, coke playing time is too long, especially large caused by cold air leakage into the furnace temperature drops to a low load; ⑺ blast furnace tube, a large number of soft drinks into the furnace; ⑻ fire protection action; ⑼ device malfunction, such as sending, fan, tripping of mill, Auxiliary disappeared.