2 ton central heating horizontal gas boilers
The third reason is that the amount of nitrogen oxide released during operation is very small. Most heating equipment such as ordinary 2 ton central heating horizontal boilerss need to use coal materials as raw materials when they are in operation. Materials such as coal generally release a large amount of hazardous air-quality substances when burned. The condensing boiler uses the steam produced by natural gas combustion as the raw material when it is in operation, so the nitrogen oxide content released during the operation is much lower than the prescribed standard. The analysis of the reason for the year-by-year increase in the sales of condensing boilers has come to an end for the time being.
Behind the low nitrogen 2 ton central heating horizontal boilers explore three popular reason is to promote the boiler heat source energy economy of power, to bring convenience to people's lives at the same time, boiler emissions also increased air pollution. Low nitrogen boiler its high thermal efficiency, the obvious advantages of ultra-low nitrogen emissions, to get people's favorite. Low nitrogen boiler reason to get popular and widely used, is inseparable from the following three reasons. 1, strong environmental protection according to environmental requirements, the country's industrial vigorously implement the project boiler clean energy transformation of small coal-fired boilers to be changed to "oil, gas or electric boilers" and other new energy device. Especially in recent years in Beijing, Tianjin and the Northwest Regional haze serious, and therefore improve the national environmental emissions requirements for industrial boilers. Beijing, Zhengzhou, Xi'an and other places have implemented the most stringent in the history of NOx emission standards (air pollutant emissions shall not exceed 30 mg / cubic meter), to accelerate the marketing process low energy consumption low nitrogen boiler. 2, the combustion more fully and more economical combustion boiler technology to more advanced low-nitrogen, and it is mainly used FGR premix combustion technology, a relatively low index of pollutant emissions, and a more appropriate fuel ratio, the combustion more fully , can significantly reduce the overall energy consumption, and its flame propagation speed is relatively fast, relatively high intensity combustion, heat can be continuously supplied in order. According to the experts explain, low nitrogen boiler requires little worried about the problem of insufficient chemical combustion. 3, high thermal efficiency boiler is an energy conversion equipment, professional production of low-nitrogen boiler as available and high-grade thermal energy necessary for life, for gas boilers, machinery (solid) incomplete combustion heat loss and heat loss is negligible ash physical Excluding. Want to improve the efficiency of the boiler, the boiler only reduce heat loss and heat dissipation reduce exhaust gas temperature. These are fast boiler for your boiler to low nitrogen summary of the popular three main reasons, whether it is national policy or market demand, low nitrogen boiler is an excellent choice. If you have a problem there are other low-nitrogen boiler operation, maintenance and other aspects, can talk to our professional boiler engineers directly by phone or online, we will do our best to help you solve the problem.
After the project identification, party fast technical staff soon made contact with our company, to our installation, commissioning, to ensure the look normal, stable use during 2 ton central heating horizontal boilers operation. Thanks fast boiler professional technical support and good service, I provide a lot of help for the textile dyeing and finishing production company. --customer feedback
Steam 2 ton central heating horizontal boilers pressure gauge should pay attention to matters 1, rated steam pressure less than 2.45MPa steam boiler and pressure gauge accuracy not only in 2.5; rated pressure steam boiler child or equal to 2.45MPa, the pressure is too spread made not less than 1.5 level. Dial gauge diameter of not less than 100mm, in order to ensure the operation of the operator to see the surface of the pressure value shown. 2, should draw the red line on the dial gauge steam boiler, he pointed out that the maximum allowable working pressure. 3, the steam boiler pressure gauge should be provided at a convenient place to observe and purging, and to prevent the high temperature affected, freezing and vibration. 4, steam boiler pressure gauge should check at least every six months once the check should seal. 5, the pressure gauge connection tube steam boiler should leaks steam leakage phenomenon, otherwise it will reduce the pressure instruction value. 6, a steam boiler gauge scale element should be compatible with the measured working pressure, working pressure, typically 1.5; 3 times, preferably 2 times. When no steam boiler gauges, pressure gauges or pressure damage did not meet the requirements of the apparatus, boiler steam pressure gauges of the following circumstances, should stop using: 1, the surface glass breaking or blurred dial scale; 2, no seals , damage or seal verification period exceeded; 3, no pressure gauge pointer finite bit staple staple can not be restored to the limit at infinite set of bits from zero gauge pressure exceeds the pressure data bits garment allowable difference?; 4, the jump table or a pointer leak; 5, other effects gauge accurate defect. The use of the accumulator: the accumulator for a hydraulic accumulator system intermittent mechanical, hydraulic fluid may be stored in the actuator output when a batch or a low speed, and the actuator requires a large flow of fast-moving, as an auxiliary energy providing oil to the system together with the hydraulic pump, oil pump and thereby achieve miniaturization of the entire hydraulic system, to achieve the object of absorbing the impact energy sudden change fast opening and closing valve and the hydraulic load, the system generates a pressure shock, pet cause vibrations and noise, and even damage the machine. The accumulator can be alleviated, which absorb fluid shock absorber pressure pulsation absorbing accumulator, and reducing the pressure pulsation and flow pulsations of various pump, thereby reducing system noise and vibration. Having a damping effect of the gas spring accumulator, it can be used to absorb the mechanical vibrations between the body and the traveling wheel of the vehicle and the like. The accumulator can be balanced upright actuator (hydraulic cylinder) and gravity load decreases when the potential absorption into hydraulic energy store, while generating the rate-limiting resistance; upright when the actuator rises, releasing the original absorbing energy accumulator , together with the pump oil to the hydraulic cylinder, in order to achieve balance and energy.